Kozeniauskas.com

Futaba T7C settings for tripple rates

savas — Tue, 24 Jan 2012 20:52:21 +0000

Hi, I bought a DLG glider named BLASTER 2. It is a second handed glider, because the new ones are quite expensive. While waiting for my plane I started researching how to set my remote right. And I faced a problem with the flying mode switch…
I looked everywhere, but I didn’t found any useful information, but I managed to configure it by my self.

E switch on Futaba T7C
(ail) to 1 at the receiver ail 2 to 6

press Mode select D/R, EXP.
D/R, EXP SW>E
CH>1-AIL (-)
D/R> 100%
Exp> + 0% (here you can chose the sensitivity of your model)

next press END and MODE (Advanced menu)
select FLAPRN
FLAPRN >ON
DIFF> +6 (select the difference between the ail movement)
AIL-2>CH6

END

select P-MIX1

P-MIX1 ON also can be OFF,depends on the switch position
MAS>OFS
SLV>CH1
SW>E (wanted position)

back using select (cursos)
P-MIX1 OFS->1

RT>+ 55% the amount is your choice. when switching E you should see ONE Aileron moving

END, P-MIX2

P-MIX2 >ON or OFF
MAS>OFS
SLV>CH6
SW>E (same position as in mix 1)

back to
P-MIX2 OFS->6

RT> – 44% (select the amount)

Video:

Building Fournier RF4 pt. 12

savas — Sun, 22 Jan 2012 20:26:21 +0000

So here is the photos of the finished plane. RTF weight is ~600 g

Building Fournier RF4 pt. 11!

savas — Sat, 21 Jan 2012 16:42:44 +0000

So this is the video of the first flight! it was quite windy and COLD! but it flies perfectly! but when I landed my ailerons broke off the tape (I suppose it is because of the cold)

Handbag cake

Laura — Fri, 13 Jan 2012 20:18:02 +0000

Poppy seed-almond sponge. Caramel+mascarpone+fresh whipped cream filling. Ready to roll icing decorations.

Sound speaker pt. 10!

savas — Thu, 05 Jan 2012 15:48:23 +0000

So I can say that this is the END! I will make the LED to blink to music and that’s about it! Enjoy!

Sound speaker pt. 9

savas — Fri, 30 Dec 2011 16:54:05 +0000

look at my speaker

Sound speaker pt. 8

savas — Thu, 29 Dec 2011 22:57:04 +0000

Hello, I got my planks

Cut the holes

the new one with the old one

And my nightmare, the wiring…

I lacked out of LED so I had to reduce some visualizations

most of the LED in place and ON

LED through the organic glass (used sand paper on one side)

Chocolate caramel cake

Laura — Tue, 27 Dec 2011 12:50:16 +0000

Chocolate sponge with mascarpone cheese, caramel and roasted walnuts filling. Fresh whipped cream, ready to roll icing decorations.

White roses

Laura — Fri, 23 Dec 2011 16:12:36 +0000

Honey sponge cake with fresh whipped cream. Sugar paste roses, chocolate and fresh whipped cream decorations.

Mickey Mouse cake

Laura — Thu, 22 Dec 2011 18:03:58 +0000

White sponge with fresh whipped cream and peaches. Marshmelow-dark chocolate fondant, ready to rool icing and fresh whipped cream decorations.